If anyone needs help here we have the DTC Database (OBD-II Trouble Codes):thumbup: Definitions for BMW diagnostic trouble codes. BMW Trouble Codes some members are having trouble getting this topic open. So I have edited your post & I am leaving a link to PDF files here your those needing. INPA BMW Software is for BMW diagnostic & coding software, INPA BMW Software work with INPA/Ediabas K+DCAN USB Interface professional performance than OBD2 Scanners, support BMW E-Chassis vehicles from 1998 to 2008. Here VXDAS.com share all about INPA BMW software & INPA K+DCAN hardware as follow. Newest BMW Rheingold ISTA-D 4.12.12 ISTA-P Newest BMW E-sys 3.33.0 3.32.1 Free Download; Free Download Op-com Can OBD2 FW 1.99 Opel Diagnostic Tool; Free download Diagbox V9.12 V7.83 for Lexia 3 PP2000 New Diagbox 9.23 Installation: Windows 10 or Windows Free download Renault Can Clip V191 V190 V188 V185 V184 V183.

• Download Free Obd2 Bmw E60 M5
• Download Free Obd2 Bmw E60 Obd
• Download Free Obd2 Bmw E60 328i

-remove bulb errors

Recommended Software: BMW INPA, EDIABAS and NCS EXPERT

How to do BMW E series coding? (Set how to activate BMW remote windows up as example)

(Plug INPA cable into the USB port on your laptop, Windows XP system would be preferred, install INPA driver and then NCS Expert software)

1. Start by creating a blank “FSW_PSW.MAN” in the WORK folder.
2. Open NCS Expert.
3. Select the appropriate profile
4. Click on VIN/ZCS/FA, select your chasis, and then select the appropriate ECU (I think EWS in the E39s case)
5. Click back
6. Click on “process ECU” and select the GM3.
7. Click the button to read the ECU data.
8. Go back to the work folder, and there should be an FSW_PSW.TRC file that has data only from the GM3. In there will be a line that says “KOMFORTSCHLIESSUNG_FB”. Under that it’ll say “nicht_aktiv”. Change that to “aktiv”
9. Click file>save as> and then where it says file type, change it to “all”
10. Save the file as “FSW_PSW.MAN” and say yes when it asks you to overwrite.
11. Now back in NCS Expert, change the job type to “SG_CODIEREN”
12. Hit execute job.

Now with BMW INPA K+CAN cable you can roll up the car windows via remote key!
K+DCAN usb for 545 e60 2005 programming and coding results

I can show you my programming and coding results few day before for my 545 e60 2005.with K DCAN usb..
Requirements for installation of ISTA P : min 200 gb free hdd,min 3-4gb RAM,and min 2ghz cpu speed,i hope you know..

I don't know for sure do you need to keep ISTA +,because I have installed Ista + before ISTA P version 3.65.0.500 which I have..
I don't remember thru that installation of ISTA P that I was needed some kind of activation key, only reg fix or something ..but anyway, now I have a new version of ISTA P3.65.0.500 so you can go thru installation of 3.65.0.500 version [85 gb]..[there is ISTA P loader folder with activation key ] Crack width calculation as per aci 318 14.

About my experience, I must tell you that with K DCAN usb cable everything was fine but slow..
For my CCC Application programming time was about 8 hours!!!
Everything else was much faster, think I have 38 ecu programmed and coded thru ISTA P...
I have done full car programming in about 12 hours!!!
Yes I know it is crazy, but when it started, I must to finish everything..

BMW ICOM is much better[and faster] solution!

But for my car it was a problem for old ZSUB numbers which I did not managed to program
all ecu-s thru WinKFP ,one by one.only few of them.
Everything about ecu-s in my bmw was from 2005 [integration level plant E060-04-09-550]

Anyway I think there is no problem for programming 1 ecu with K DCAN usb, but keep in mind that voltage of the battery must be backup all the time and key must be on ignition position ..
And one more thing, for me WinKFP is also good solution for programming, because when you have new ZSUB numbers {ecu numbers} ,you just need to find that number in AIF thru INPA, and after that you just in WInKFP comfort mode [F1] ,put that number [F1],enter VIN [F4],than DONE[F8] and than [F3] again and everything is done!
Or just update ecu with [F3],than select ecu family,enter VIN [F4],than [F8] and again [F3]..

Download Free Obd2 Bmw E60 M5

I hope you don't mind for this long thread, and also sorry for my English writing ,because I don't know better..

Download Free Obd2 Bmw E60 Obd

PS:ISTA P is only for programming and coding ,not for diagnostic..so keep your ISTA +

BMW E60 ISTA /P final report:

Download Free Obd2 Bmw E60 328i